BOP 系列可程式 4 象限電源供應器

TO->

SPECIFICATIONS		RATING/DESCRIPTION	CONDITION
Type of Stabilizer		Voltage/Current 4-quadrant	Switch mode
Switching Frequency		100KHz ±5%	Output stage
Source Adjustment Range	voltage	-100% to +100% of rating	Output stage
Source Adjustment Range	current	-100% to +100% of rating	0-50°C
Sink Adjustment Range	voltage	-100% to +100% of rating	0-50°C, recuperated energy is sent back into line for general reuse
Sink Adjustment Range	current	-100% to +100% of rating
Voltage Stabilization in Voltage Mode	source effect	0.05% of rating	min-max input voltage
	load effect	0.1% of rating	0-100% load current
	time effect (drift)	0.02% of rating	0.5 - 8 hours
	temperature effect	0.02%/°C of rating	0-50°C
	ripple	2% Eo max p-p	Includes switching noise
	noise	0.2% Eo max rms	Includes switching noise
Current Stabilization in Current Mode	source effect	0.05% of rating	min-max input voltage
	load effect	0.2% of rating	0-100% load current
	time effect (drift)	0.02% of rating	0.5 - 8 hours
	temperature effect	0.02%/°C of rating	0-50°C
	ripple	2% Io max p-p	Includes switching noise
	noise	0.2% Io max rms	Includes switching noise
Error Sensing		0.25 volts per wire	Above rated output
Transient Recovery in Voltage Mode	maximum excursion	5% of nominal output	nominal voltage, 50% load step
Transient Recovery in Voltage Mode	recovery time	200 μsec	Return within 0.1% of set voltage
Output Common Mode Voltage		300V	Output to chassis ground
Series Operation		Master/slave	Maximum of 3 identical units, up to 300V max.
Parallel Operation		Master/slave	Maximum of 5 identical units
Output Protection Limiting		Voltage and current limited in four quadrants
Output Stage Protection		Output overvoltage / overcurrent, heat sink over temperature, switchers overcurrent	Triggers latched shutdown protection of the output module and PFC stage. Recover by cycling power off, then on or by pressing RESET at the front panel
Input Stage Protection (PFC)		Internal overvoltage, undervoltage, overcurrent, heat sink overtemperature, fan inoperative
Input Stage Protection (PFC)		Input circuit breaker overcurrent
Small Signal Bandwidth	voltage channel	2 KHz maximum	Into nominal resistive load
Small Signal Bandwidth	current channel	800 Hz maximum (600 Hz Maximum) (note.1)	Into short circuit
Analog Control	voltage or current main channel	-10V to +10V	Full range output
Analog Control	voltage and current protection limit channel	+0.05V to +10V	0.5% to 100% of nominal range
Digital Control	local	Panel-mounted keypad
	remote	IEEE 488-2 (GPIB)	SCPI
	remote	RS 232	SCPI
	remote	RS 485 (BITBUS)	Used for series and parallel configurations
Display	front panel	4" backlit LCD displays all functions
Display	remote	All parameters read back on RS 232 and GPIB buses
Rise/Fall Time	voltage channel	250/200 μsec	Into nominal resistive load
Rise/Fall Time	current channel	0.7/1.2 mSec	Into short circuit
Input voltage	nominal	230Vac 50/60 Hz	Single phase
Input voltage	range	176-264Vac 47-63 Hz	Single phase
Input current	nominal type	176Vac - 9.5A(7.5A); (note.2) 264Vac - 6.4A(4.4A); (note.2)	Maximum
Temperature	operating	0 to +50°C	Full rated load
Temperature	storage	-20 to +85°C
Cooling		Two internal fans	Exhaust to the rear
Humidity		0 to 95% RH	Non-condensing
Shock		20g, 11msec ±50% half sine	Non-operating
Vibration	5 -10 Hz	10mm double amplitude	3-axes, non-operating
	10-55 Hz	2g	3-axes, non-operating
Altitude		Sea level to 10,000 ft.
Dimensions		133.3 x 482.6 x 546.1 mm	H x W x D
Weight		24.1kg

note.1 : BOP 6-125MG only.

note.2 : BOP 6-125MG and BOP 10-75MG only.

上一頁

下一頁

以上規格及選購配備僅供參考，實際規格以KEPCO網站資料為準，或洽本公司業務人員